'ALARMS'

victor from CARSON CITY NV (Contact Member) -

CAN ANYONE HELP I HAVE THIS LIST OF ALARMS AND CAN NOT CLEAR THEM.

Alarms found on machine model SL-OB

M/N 731

Yasnac controller MYNC-L1

342: servo error (z)

341: servo error (x)

310: servo off

202: ot (z)

201: ot (x)

400: seq error2

175: mem error (marc)

174: mem error (keep)

173: mem error (prm)

172 mem error (set)

Comment #1 bachir (193.194.92.5) -

please could you give the solution of probleme of alrame (al 05)of emco f1 cnc

and what i do

good luck

think you

Comment #2 kamran (125.209.115.133) -

There is an alarm on the machine display . “A102 Electric Cabinet temperature too high”.In the cabinet, output from +D1-E1 is checked on terminal +M12-X1 (d20) and it is 24V.This is input for Diode Matrix Card. This card has 32 Opto-Couplers which have been checked. This Matrix card has four Rows as SCN0, SCN1, SCN2, SCN3. The problem is with SCN1, which does not go low whereas SCN0 goes low. This is compulsory to read inputs from the machine. One of these inputs is Electric Cabinet Temperature. ON FX 63 CARD, the output of ROM 4A makes address for 3 to 8 line decoder 74LS138 (B4). One output of this decoder is Clock Pulse CP for latch 74LS273 (K7). The 4-bit data for this latch comes from a transceiver 74LS640 (E4). The output of this data latch is input for another open-collector decoder 7445 (L7). The output of this decoder generates Row inputs (SCN0 ..SCN3) for Diode Matrix card.

The problem which I have known is with the 4-bit data input for transceiver 74LS640 (E4). I want to know about this data. From which PCB of the system TX8D, this 4-bit data is generated for this transceiver (E4). Please mention the I.C. on that PCB.

Comment #3 DAVID NAVARRO (69.44.67.158) -

I HAVE A ( 1093: MEMORY ERROR ( OFS ). ON A YASNAC CONTROL. WHAT CAN I DO TO CLEAR IT?

Comment #4 david navarro from santa ana,ca. (Contact Member) -

1093 MEMORY ERROR ( OFS ). ON A YASNAC CONTROL. WHAT CAN I DO TO CLEAR IT?

Comment #5 sandeep (59.96.173.16) -

Plese send me daily alarm of fanuc series OT, Oi and sinumerik 810D cnc comtrollere with solution.

Comment #6 KARTHI from BANGALORE (Contact Member) -

i am facing a problem in the siemns 802d system.during axis moment in jog mode at100%.

i got a following error in one side was very high and another side was ver low.what i will do i get a same values in both sides.

Comment #7 ravi (58.178.108.15) -

hi guys,

i own a hyundai cnc lathe with sinumerik 840c controller, along with barfeeder ( bartec). When the machine is turned on the 9115 alarm appears on the screen and im unable to figure the way to reset it.

Would apprecite if any one can suggest to fix the problem.

Kind Regards,

Ravi

Comment #8 Nicolas (71.41.127.146) -

mazak vtc-20c I lost my home positioning, how can I get my home axis positioning back again?

Comment #9 shan (202.125.143.74) -

i have problem in my macjine servo dgtlparameter alarm in x&z axis.machine made by colchester tornedo 100 by fanuc OT.i entered all parameters of x&z but alarm can't rest plz tell me about it

Comment #10 Richard (12.21.164.238) -

Can anyone help me with the following alarm and how to clear it.

on Mitsubishi MPA V55

Alarm: 820B Bubble I/O ERR

Comment #11 matt tucker (166.128.142.248) -

I have a 400 servo alarm on my mazak 15 nc machine. can anyone tell me what that alarm is?

Comment #12 Navid (70.50.51.107) -

I have a hass VF4 APC cnc machine, today i was runninig a part

that contains two tools whit coolant throw the spindle, one of

the tools is working perfect but for the next one you see

after tool gets ready to run(coolant is coming throw the tool

and spindle)tool stops(feed stops), you see alarm 151, says not

enough coolant or dirty filters.I changed coolant and cleaned

all filters.but still same problem.

Comment #13 sagar (123.239.158.128) -

system error in yasnac j300 vmc machine

Comment #14 A.SAGAYARAJ (218.248.69.16) -

While running the spindle more than 1000 RPM , We are getting alarm 1016 , and in FANUC bord AL-23 /Can you please sugesst to solve

regards

Comment #15 Michael (75.146.90.197) -

"Maintenance"

I hope you can help me with the problem i am having i keep getting an alarm that says 55y servo lag on my y axis the machine will jump and then shorlty after it will turn off. If you have any info on it please let me know.

Comment #16 MAHESH from DELHI,INDIA (Contact Member) -

"YASNAC ALARM"

please could you give the solution of problem of alarm on YASNAC J300.

alarm: SYSMON RAM ERROR# 7

Comment #17 Art (24.10.74.25) -

"Fanuc alarm NO 2000 axis interlock"

Fanuc alarm No 2000 axis interlock on a supermax rebel.

Comment #18 Stevo1 from USA (Contact Member) -

"open door"

Art,

You have an interlock switch somewhere on the machine. This would typically be a open door or something along that line.

Stevo

Comment #19 Rizk Negm (41.233.153.6) - Fri Feb 12 23:56:50 2010

"cairo,Egypt"

problem with cnc machine from chiron FZ18W

message" side door not closed or locked "

the machine stop

Comment #20 todd (12.171.25.67) - Tue Mar 9 01:57:20 2010

"tech m&a"

701 alarm on a makino a66

Comment #21 Navid (81.90.152.135) - Sat Mar 13 02:58:52 2010

"Maho 700 c error!?"

Please help us with the error number X05 when I finish refrence on that device (X)?

E-Mail:         

Name:            (required)

Title:           (required)

Message (do not enter emails or links or urls in the message!):