• Page 1 (Original Post) •
william rachels (63.24.62.204) -
Has anyone had a problem with the older sl2 mori seki(1970 something) lathes loosing the parameters and the program? poooff everything gone???this lathe has the yasnac control 2000g.memory board shot maybe ?? And any good sites where to buy vintage replacement parts? Any help would be greatly appreciated. Thanks ,William
Comment #1 Bill (71.116.45.215) -
Maybe a bad battery backup. Ive seen this when the battery gets old and the power flickers
Comment #2 william (63.24.113.80) -
thanks Bill for info,I did check the battery back-up and it checks at 3v.which is ok.What I did find out that it was a memory board which I purchased at yaskawa,exchange for about $1300.the machine is back up and running.some places I looked for the same board was $2800!(exchange).It pays to shop a little.
Comment #3 Oscar Quintanilla (189.163.204.74) -
Somebody can help me I need to get the manuals for a SL-3b with a yasnac 2000g control, If some body have info on this I will paid for a copy of this machine and controlthanks
Comment #4 Oscar Quintanilla (189.163.204.74) -
email oquinta@prodigy.net.mx
Comment #5 Dave K. (64.19.74.235) -
I need alarm codes for mori seiki 2 axis lathe.This number was on the controller MSX-850 111. This number was on the machine NL51FG2215.Can somebody help me>
Comment #6 vikas (59.94.252.220) -
I DONT HV OPERATOR MANUAL FOR 2000G NUMERICAL CONTROL FITTED IN SL2 MOREI SEIKI LATHE .I SHALL BE GREATFUL IF ANYBODY CAN HELP ME OUT OR ANY BODY WHO CAN HELP ME IN PROGRAMMING THE MACHINE THANKS
Comment #7 ramon (201.160.223.16) -
quiero saber si me pueden ayudar, con una alarma num. 25 no se la pueso quitar
Comment #8 severiano perez (67.126.242.54) -
hello i nede in informechin hwo ken teike in alarm 0582 momory collating error
Comment #9 Mark Rice (70.251.7.28) -
Memory loss of Y2000G/G2 controls is often caused by loose cablesbetween the sections of the control, and e-proms backing out. Try reseating all the cables and the proms (found on the master board and the ladder board). Also check your 5 volts on your power suppluy. It should be 5.0 to 5.15 volts. Check it in the AC range and make sure there is no ripple. I have access to some operators and programming manuals, but they are ratty (pages separated). I have a fairly complete copy of the schematics, but it is a copy of a copy of a copy, so I have had to pencil in places where it is hard to read. No, I don't have a pff of them, they are some odd page size (neither B nor C) and don't fit a scanner. If you call Yaskawa, there are still a couple of guys who know the control, but most of them won't tell you squat. As far as the spindle drives go, just replace them with AC motor and drive, and have done with it. It is cheaper than trying to get those old drives and motors repaired.
Comment #10 JOSE (64.12.116.139) -
I JUST BOUGHT A 1982 MORI SEIKI SL3 WITH YASNAC 2000G I NEED ATIP OF WHAT SOFTWARE FOR MY COMPUTER TO PRORGRAM THANK YOU
Comment #11 Veravat (203.147.0.44) -
I want total alarm list CNC Mori Seiki , Model : CL2000B
Comment #12 Gus (68.0.146.204) -
I have the manuals for an SL-4 with yasnac 2000g. I have had the machine since new and it is the best. I have been programing and running the machine and know it well. If you have specific questions maybe I can help. Se habla espanol.
Comment #13 Anthony Hanna (206.19.210.8) -
we have a mori seiki SL-25M LOCKED UP IN mdi UNABLE CLEAR FAULT??
Comment #14 rob radak (69.95.63.105) -
Does anyone know how to utilize the tool-measure feature on the yasnac 2000?
Comment #15 Jason (76.186.105.104) -
We are closing our doors to our great machine shop to move on to new places and we have a machine that has always served us well. It runs great and holds great, it just needs a new power supply. Its a Mori Seiki SL2 with a Yasnac 2000 G Control, with BTR installed. All tool holders will be included with the sale. The machine has not been used for about 4 weeks. This machine is also equipped to communicate with your PC. For those of you who have used this model you know what a great find this is. If you are interested or have questions feel free to email away! We are asking 4500.00 or best offer for this. Buyer must arrange pick up. If you are wishing to use single parts of the machine to replace on an existing machine that may be an option as well.
Comment #16 Mr Opas V. (125.25.57.6) -
I have read from comment #9 Mark Rice (70.251.7.28 ) I got the same proble, could you please directly contact me, thanks.Best Regards, Opas
Comment #17 Nahuel Gorosito (201.252.212.19) - Mon Mar 8 18:47:33 2010
"CNC Apprentice"
Hello, I have a Mori Seiki SL 2 Yasnac 2000G, I was wondering if anyone could give me some tips on basic step by step programming, I'm having trouble writing more than one block on a program. I'm not sure if its the EOB button thats not working or if I'm punching it at the wrong time, any help would be greatly appreciated. Thank You! • Page 1 (Original Post) •
| You are not logged in. It is recommeded that you post messages
and comments with a CNC Machine profile. You will be protected from spam and have more features. Registration is quick and easy. You can also post as a casual user with the form below. As a casual user your IP address will be published! You must be a registered used to include a link. |
|