'FANUC OM Controller Program load'

FANUC OM Controller Program load

Richard Williams (146.201.232.84) -

I have question regarding our old Fanuc OM controller…

We had a 101 error(Please clear memory)

I cleared the memory and then needed to reinput the tool carousel subroutine which is a O9000 PROGRAM. The 09000 programs are protected and when I input I am getting an 074(Illegal program number) code.

I have also occasionally gotten an 087(buffer overflow message) that lists as the I/O unit or PCB is defective.

Does anyone know the controller settings on how to download the tool carousel O9000 program?

Thanks

Comment #1 Steve (2) from Wisconsin (Contact Member) -

To load and unload 9000 programs there is a parameter that write protects these programs. I do not have a OM control parameter manual. But you will have to set PWE parameter to 1 then change the parameter that write protects the 9000 programs. This parameter blocks loading and downloading 9000's.

As to the buffer overflow this is a common alarm when your settings between your computer and your machine are off. The easiest thing to try is slow down your baudrate. If this does not work on your computer go to SYSTEM icon in the control panel under HARDWARE, DEVICE MANAGER, drop down the PORTS list, click the port your DNC is using, click PROPERTIES, PORT SETTINGS, ADVANCED, set the FIFO to it's lowest setting, and click ok when exiting all menus.

Good luck!

Comment #2 mehdi.b (78.38.77.3) -

I had a similar problem with our old fanuc OM. I put the input button and sent the nc file. but I just saw the LSK (not the input) in the screen. And I didn’t see the 087 or 074 errors.

I set the PWE to 1 but I had this problem yet.

Comment #3 Dave Reid (82.37.84.12) -

On a fanuc omc controller what is the parameter No

for G43 tool lenght offset cancellation

i wish to have G43 active at all times

but lose the offset when returning the z axis to home

on a G30 movement

Comment #4 Stevo1 from USA (Contact Member) -

There is no parameter that can keep G43 active at all times. This must be programmed. However there are ways so you don't have to worry about instating your G43 code. I do extensive macro programs for all my fanucs/machines. I always set my G43H# in the tool change macro. This works great because at the start of each operation you should always have a tool call. I also set my speeds and feeds in the macro this way I don't have to program them throughout the program.

This will depend on your machine type and how the MTB set it up. I had an issue with the MTB not allowing a M6 when you are trying to call the same tool that is in the spindle. This is ok in my macros as I can bypass the tool change but if you just wanted to active the H you couldn't use the tool call M6. Work around was to create a custom M code to instate tool offsets and S&F's. Took all of 10min.

Stevo

Comment #5 poucet28 (90.20.21.196) -

if you get the LSK and nothing enter in the machine, and no alarm occurs, your RS port is dead .

On a Fanuc O B or C , you can try the second port .....

Comment #6 muhammed (85.98.123.38) -

hi; my problem how to input to # at fanuc o-m controls

Comment #7 G. SRINIVASA RAO (122.169.212.241) -

Dear sir,

Today I worked fanuc om controller how run the programm with dnc system, or tap mode

Comment #8 Thanh Doanh (125.212.221.149) -

DEAR SIR !

I NEED BLOCK DIAGRAM SCHEMATIC CNC MACHINE KURAKI

MODEL : YK-435

CAN YOU HELP ME .

THANK YOU VERY MUCH

GOOD LUCK TO YOU

Comment #9 PEDRO SANCHEZ (190.25.229.181) -

Please to send infomation the parameter 9920 and 9930. i need interpolation helicoidal mill

thank

Comment #10 Pedro Sanchez (190.25.229.181) -

sorry the control is Fanuc 21M.

Comment #11 W.G.GAMINI (124.43.58.242) -

DEAR SIR,

SPINDLE NOT ORIENTATE, ENCODER SIGNALS OK.

SPINDLE IS HUNTING.

HOW TO ESTABLISH MY PROBLEM.

THANK YOU

GAMINI.

Comment #12 Stevo1 from USA (Contact Member) -

some machines are equipted with a magnetic sensor on the side of the spindle that tells it where the orentation position should be. Replace or clean the sensor.

Stevo

Comment #13 David (206.80.83.67) -

Can someone give me an idea of how to get rid of an alarm 408 serial not ready on a chiron om control.have tried new spindle amp, new memory card, new spindle encoder, new fiber optic cable and adapter.

Comment #14 Fred (60.241.43.170) -

Hi pls, does anyone know where to buy or get a FANUC PC SIMULATOR?

I have only been given a price from Czech Republic and the price was just too much.Please help if you know anyone else who sells this PC SIMULATOR and Guide.

Thank you Fred

Comment #15 TOPGUN from Rock Hill, SC (Contact Member) -

David have you been able to correct your problem with the 408 alarm on your Chiron? If not contact me I can help.

Comment #16 david (3) from New Albany,Ms (Contact Member) -

TOPGUN,

No i have not corrected this alarm.Any help you could give would be appreciated.

Comment #17 david (3) from New Albany,Ms (Contact Member) -

p.s TOPGUN how do i contact you?

Comment #18 TOPGUN from Rock Hill, SC (Contact Member) -

David,

Do you have yahoo messenger? If so my user name is topgun6113. We can take it from there.

Comment #19 david (3) from New Albany,Ms (Contact Member) -

no, cannot run messenger on our server but i can use email account paul.kennedy@piperimpact

Comment #20 TOPGUN from Rock Hill, SC (Contact Member) -

David,

I have sent you contact information to the email you posted. Hopefully it was .com at the end LOL.

Comment #21 VIMAL (121.245.133.35) -

GOOD MORNINIG FRIENDS,

CAN SOMEONE PROVIDE ME LADDER DIAGRAM/DATA OF TAKISAWA MAC V1-E VMC(DRILLING AND TAPPING CENTER) WITH UMBRELLA TYPE TOOL INDEXER?THE MACHINE IS WITH FANUC O-MC CONTROLLER.

THANKS,

VIMAL

INDIA

Comment #22 Luis Marin (190.71.116.253) -

I have a trouble in the sakazaki CNC with OM fanuc control.

I need to look optional parameters because don't move in G28

when operate in automatic mode.

I need pulse handle parameters.

Thanks and regards.

Comment #23 Stevo1 from USA (Contact Member) -

G28 is not a Fanuc option and should work. If it were an option and it was not activated then it would give you a “Improper G-code” alarm when it is programmed. Post your code on how you are programming the G28 and explain what it is doing wrong.

I am not 100% on what you will need to get your handwheel working but try 900.2 for interrupt and/or 900.3 for 1pulse hand wheel. 902.0 is for 2 pulse.

Stevo

Comment #24 isaac (189.156.61.226) -

nesesito programa o secuencia de comandos para cambio de herramienta en maquina takisawa serie OM, programa 9001

E-Mail:         

Name:            (required)

Title:           (required)

Message (do not enter emails or links or urls in the message!):