'Fanuc 15 M'

Fanuc 15 M

SIAVASH (87.107.38.64) -

I HAVE A PROBLEM WITH FANUC 15 M RAM PARITY ERROR WOULD YOU HELP ME IN THIS WAY.

Comment #1 sedat (81.214.57.110) -

you have to call to fanuc service and help them. because your sram can be faulty or fistly you can open with del and reset button,after this operation load system and sram files.if this alarm occur again,please call to fanuc.

Comment #2 DILIP (59.95.21.57) -

i thinnk your bubble memory card must be faulty.

firstly you have to clear parameter and program with procedure

stated in manual.

important - please check that u have parameter back up

Comment #3 star123 (220.226.172.250) -

Thanks dilip for your excellent help. I never know about this and always spend more money behind them. Its works for me.

Comment #4 guns from INDIA -

even i had a ram parity error and got out of it by clearing up all the programs and re-entered all the parameters too..the problem now is that i'm not able to enter the subroutines and the controller type is fanuc15m-f somebody pls. help me out..

Comment #5 ansari (217.218.149.194) -

in the name of GOD

your RAM has lost some of its data.

you must clear all data and then reentering parameters(via rs232)

for more informaition you can mail to me.

best RGD

ansari

Comment #6 senthil kumar kathirvelu from india -

can u send me a program for simple pocket with corner radius

Comment #7 neil (87.127.74.114) -

Fanuc 15 spares and repairs

Comment #8 PATRICK (70.55.177.113) -

Im having a problem with arcs in Z ....

exaple :

N110 G02 X2.750 Z-0.750 I0.500 K0.750

it only make a strait downword line instead of an arc

Am i missing somethikng ?

Comment #9 Jitendra Raikwar (122.168.120.187) -

I am facing problem in 840C Control. PLC program is corrupting in between operation after running some time. There is no power failure in between as UPS supply is provided to machine. we have to load it every time. why this is happening. I have checked the 24 VDC Power input supply to control is OK. Request Help.

Jitendra

Comment #10 jayesh vasani (59.95.208.90) -

How we can change language in fanuc 15m ?

pl guide us

regards,

jayesh

Comment #11 Moises (189.166.151.179) -

Siavash: you must clear all data and then reentering parameters, use hyper terminal(windows) or procom (symantec), in some CNC like 15Ma you need a psw

Comment #12 adeem from pakistan -

I have 4 axis CNC milling with FANUC 15M controller. an error occured when replacing batteries in OFF mode "RAM PARITY ERROR"

now the problem is that the connection from PMC to NC

plz help me out????

Comment #13 Deepak Bodhani from Pune, India -

Dear Friends,

We have a portable terminal called DIGI-HHT / LK which helps in taking all your CNC program files, NC data, PLC data etc before you clear the memory of FANUC for whatever reasons. After rectification, you can re-load all data back to FANUC in no time, via RS-232 port. Read more at digitech-engineers.com

Comment #14 Jonny from Orlando, FL USA -

My friend bought recently a KOMO router with a FANUC 15-M . We are trying to send a initial parameters ( zero points for each axle) from his computer but some is wrong. We tried some configurations found in Internet for the COM ports but still not working. Next suspect for us is the cable and connectors. Somebody know how most be each wire in both ends for a DB25 at the machine and DB9 at the computer?

Thanks

Comment #15 Steve (2) from Wisconsin -

Guns

Sounds like your subroutines are probably 8000 & 9000 program numbers. You have to go to settings PWE parameter should be 8000 change = 1 go to service parameter 2201 bit 0 set equal to 0 this allows editing of 9000 programs then should be able to load. If it is 8000 program numbers then it is parameter 11 bit 0 set equal to 0.

Comment #16 Anil Kumar Acharya (210.18.123.42) -

We are having a Makino make CNC machining center with fanuc make 15MA .All the datas were lost of its own.We have entered the required parameters thru backup.still m/c pmc is not getting on and m/c is down.

Comment #17 Steve (2) from Wisconsin -

Did you reload your PMC backup? Go to your CNC/PMC softkey and check that all your data is correct and your ladder is loaded. Did you set your option parameters correct? Parameters 9100 and up.

Comment #18 GISHOLT (85.154.155.207) -

In Daewoo HMC H80, I have alarm - B axis zero return. i.e - 0T 032 B NEED ZRN (ABS PCDR) . Can any body help me to fix this alarm. I think need to set in parameter.

Rgards,

Gisholt.

Comment #19 HITEC - SHIVAKUMAR (59.92.120.221) -

Hai patrick,

Before and after G02 check your G code, please avoid I & K value and use R value for radius machining. check your tool nose compensation as well. your tool radius should be less than your program value. In case of complication program please send drawing.

cheers,

Shiva

Comment #20 ravinder (118.95.68.181) -

i wants to change the ladder of 15m any body hv the editing softer

Comment #21 lee (203.160.1.72) -

I having a problem with my OKK machine .The Y- axis is not enough of length and I can not entering to the troke limit .Somebody help me pls.Thanks

Comment #22 Shree from Pune india -

Dear Mr Anil

On makino machine pmc is written in c language , and cannot see in the laddle format , after curuption of nc and pmc parameters u have to load pmc parameters manually so that communication between cnc and pmc starts. By pressing cnc/pmc key u may enter to the makino screen, if pmc parameter are healthy u can acess the manu otherwise system gets hang and u require to switch off and on again.pl define ur machine model, i may be able to help u .

Shree

• CNC Machine" target=_blank>problem on makino machine

Comment #23 Farhad (213.217.33.82) -

Hello ...

I need maintenance manual of "FANUC 15MA" cnc controller.

please send me it by e mail "tedy5555@yahoo.com

Thanks

Comment #24 Rizwan (195.229.237.38) -

i have fanuc control for Vertical milling machine . now the tool changing time has increased to 40 sec as compare to previousely few seconds. also there is error 2030 .i donot know why the tool is changing time has changed so much .what may be the reason ?

Comment #25 Stevo1 from USA -

Is there any message with the 2030 alarm? Is it on your message screen or alarm screen?

Were is the time difference in the tool change that it takes that much more time? Is it moving to the magazine slower? Is it just sitting there for a certian time? You should be able to do a tool change and watch it through and tell me were all the time is being taken up.

Stevo

Comment #26 Rizwan (195.229.237.38) -

Attn: Steve

the error 2030 came on message screen.

while the the delay in tool change is when the POST need to pick the next tool . so the time delay between one tool to place and to pick up the next tool.

Comment #27 Rizwan (195.229.237.38) -

Attn : Stevo

i explain again the delay is due to magazine Is just sitting there for a certian time. The Magazine move with right speed there is no problem here . but then to place the tool ( tool of finished job ) but stay there for more time ( delay ) and again go up and pick up the next tool .

Comment #28 Stevo1 from USA -

Ok if I understand correctly the magazine just sits there and does nothing for a certian amount of time, correct?

When you look at the program what codes is it sitting on? The M6, the T-value, small positioning?

Sounds to me like the machine is waiting on a signal for some reason. Now if you were to just do a T5 call(pre-call a tool) to the wait arm. Does the tool magazine still just sit there for a peirod of time?

What kind of Fanuc control are you using? Also as before is the 2030 alarm an "Operator" message or "Alarm" message? The way to determine this is when the alarm is active which softkey do you have to select to view the alarm? Does it give a description with the alarm on the screen?

Sorry for all the questions but details help ALOT.

Stevo

Comment #29 Chintan Patel (93.134.12.64) -

The datas from the Bubble memory is lost over a Makino HMC with Fanuc 11; Any one knows or can load in India ?

We have also problem with pallet changer function in auto mode over other 5 pcs. Makino HMCs with Fanuc15. They were with pallet pool but now not. It works in manual but not in auto-mode. Similarly problem with tool changer as there were tool bank at previous factory. All kind of helps will be appreciated.

Chintan Patel

Www.patel-tech.com

or call Dipak patel at 0989884 2566 in India

Comment #30 Kishore K Gupta (122.162.245.224) -

We use over 50 CNC machines and are in need of System Parameters of 0im , 0ma , 0mb, 0mc, and 15m .any person having this may kindly forward it to pyn@airtelmail.in

Comment #31 Todd (24.34.87.202) -

I have a dynapath delta 20 controler. I lost power for 10 days and lost all the info in the machine. I reentered what I think is the right travel limits and back lash. My problem is when I try to program I get an error code PPS Overflow and I don't know what it is. It's not in the manual as an error code.

Please Help me

Thanks

Todd toddfourn@Yahoo.com

Comment #32 Stevo1 from USA -

I don't know anything about your controler but the PPS Overflow sounds like "part pogram storage" overflow. Could it be that you do not have enough memory for the programs that you put in the control?

Stevo

Comment #33 Prasanna (1) from Nasik - Fri Jul 3 02:52:53 2009

The BFW HMC after a weekend when we try to start following list of alarm and could not be started please help

Alarm list:417;servo alarm x axis digital parameter

417;servo alarm y axis digital para.

417;servo alarm v axis digital para.

466;y axis motor/amp combination

466;z axis motor/amp combination.

5138;fssb axis setting not complete,

Name:           
E-Mail:         

Optional (please add to our directory first)
Web Link:       
Link Title:     

Message: