CNC Machine Logo
CNC Machine forum Logo
Last update: 03/18/10 15:28
CNC Machine RSS Feed Computer Numerical Control
Mitsubishi

'S01 Servo Alarm:PR'


• For the ultimate in speed: Up to 4000 ft @ 115.2 kbaud 12 times faster! •

Post your related message now.
Industrial RSS Feeds
Local Directory



CNC Machine Forum --> Read New MessagesPost New Message



(Login / Register)


Interact
  • Tweet This
  • Facebook This
  • Photo Gallery
If you have any questions or comments, please post a new message or a follow up.
Related Resources


Top Searches: • mazak alarm codes • s01 servo alarm • s01 servo alarm pr • mazak alarm list • mitsubishi s01 alarm • mitsubishi cnc alarm list • mitsubishi alarm codes • okuma servo amplifiers • mazak fault code • mitsubishi cnc alarms • servo amplifier alarm f1 • mitsubishi servo power supply alarm • servo alarm pr 003a • mitsubishi servo alarm • mitsubishi spindle amplifier • cnc s01 servo alarm pr 003a • mitsubishi servo alarm e7 • mitsubishi servo amplifier alarm f1 e7 • mazak alarm codes • mazak alarm list • mitsubishi servo alarms • servo alarm 32 • s01 servo • so1 servo alarmi • so1 servo alarm • e7 inverter alarm • mitsubishi servo amplifier • servo amplifier mel • meldas servo alarms • mitsubishi alarms list • e7 mitsubishi inverter codes • mitsubishi inverter codes •
More: Mitsubishi

S01 Servo Alarm:PR


Page 1 (Original Post)

RRL (72.128.219.159) -

Asking for expert advice for S01 Servo Alarm:PR fault with Mitsubishi Medlas 520LR CNC Control

Comment #1 Marcus Clayton from Melbourne Australia (Contact Member) -

S01 will have a code (up to 4 digits) and then an axis after it.

example S01 003A X means overcurrent alarm on X axis.

Check servo modules in cabinet and they will be flashing alarms. One will have 003A, the fault, and others will flash E7 which means fault on another axis.

If you can identify the alarm you can have a good guide to the fault. In the above case the most common cause is a bad ballscrew bearing or swarf build up causing an overload in the motor


Comment #2 rrl from Midwest (Contact Member) -

Marcus thank you for the information.

The full servo alarm code is: S01 Servo Alarm: PR 0032S1 and it occurred during a Z axis drilling operation.

Fault codes on the servo and spindle amplifiers are as follows:

Axis Amplifiers:

Flashing F2 E7 and F1 E7

Spindle amplifier:

F3-32

Inverter Power Supply:

6

Is there a list of these faults available on the internet to find out more information.

Thanks and how is the weather in the "Down Under"


Comment #3 Jokin (125.161.12.177) -

Hello ,

Its mean your spindle amplifier is out of service, please exchange with anew one or repair it with Power Module.


Comment #4 cynthia madison (216.171.183.162) - Tue Feb 2 12:12:25 2010

"machine repairperson"

getting spindle amplifier alarm on MITSUBISHI CNC SHAVING MACHINE FC30CNC(4-AXIS)(FANUC 21-MB)- have replaced headstock, tailstock, and cutter head support bearings-still--machine runs for a time and then faults out(before life of cutter tool should be up). we reset n it runs for a time and then repeats problem-no excessive heat in spindle- pressures are set correctly AND-- the parts r coming out great! do u have any idea what is going on with this machine(before they keep changing parts!)what the heck does a spindle amplifier do anyways?! help!!


Comment #5 Stevo1 from USA (Contact Member) - Tue Feb 2 15:20:44 2010

"alarm number"

What is the alarm number??

Stevo


Page 1 (Original Post)
You are not logged in. It is recommeded that you post messages and comments with a CNC Machine profile. You will be protected from spam and have more features. Registration is quick and easy. You can also post as a casual user with the form below. As a casual user your IP address will be published! You must be a registered used to include a link.

REPLY to this message:

S01 Servo Alarm:PR; Mitsubishi

OR

Post a NEW MESSAGE

33

Please submit a new reply here. HTML is not allowed and you are encouraged to seperate your paragraphs with a double blank line for readablity. Please make sure your message is relevant to , Mitsubishi, and this message:

S01 Servo Alarm:PR; Mitsubishi
E-Mail:         
Your email address is required. It will not be published.

Everything you enter below will be published.

Name:            (required)

Title:           (required)

Message (do not enter emails or links or urls in the message!):

You must be registered and logged in to include a link with your message. Others will also be able to contact you without disclosing your email address.
Submit Reply. Please do not submit the same message more than once.



Have you added a link to us from your website? (2751):
  • <a href="http://forum.thecncforum.com">CNC Machine</a>
  • <a href="http://forum.thecncforum.com/Mitsubishi">S01 Servo Alarm:PR; Mitsubishi</a>
S01 Servo Alarm:PR; Mitsubishi All trademarks, copyrights and brands are the property of their respective owners.


(wezuzeepzwwt)

Privacy & DMCA Policy -- Those who twitter us!
Mitsubishi 'S01 Servo Alarm:PR'