Advertisement: Free Ad
Recent Notes and Tags
Top Searches: • okuma alarm list • okuma alarm codes • nice alarm registration code • okuma lb25 • okuma alarms • okuma lb 25 • nicealarm registration code • okuma alarm codes • nice alarm code • okuma lb 25 • nice alarm registration code • okuma alarms • okuma parameters • okuma alarm list • nicealarm registration code • nice alarm code • okuma lb25 • okuma alarm • okuma alarm 119 • okuma alarm • okuma parameters • nice alarm key • okuma alarm code • okuma lb 4000 • lb25 okuma • nicealarm code • registration code nicealarm • alarmas de okuma • okuma alarm code • okuma cnc alarm codes • alarmes okuma • registration code nice alarm • |
OKUMA LB 25 ALARM CODE 119 - Okuma
| OKUMA LB 25 ALARM CODE 119WHEN I SWITCH FROM O.D. JAWS TO I.D. JAWS IGET A ALARM CODE 119 JAWS OPEN.HOW DO I CORRECT THIS...THANKS |
|  More info needed. Most likley the prox switch needs to be adjusted on the back end of the hydralic acuator for the chuck. jg |
| I think you might need to reverse a switch or hydraulic valve to change the pressure switch input from inner/outer clamping. see manual for chucking signals. |
| Tengo alarma en plca SVC E 480 770-015-B ... Led VR encendido ....que es ????????? no tengo manuales ... ayuda |
| hi have a nice day ı think your problem 1 swiçh 2 adjust position 3 soft wear |
| last time ı have a this proplem we change a soft wear after than alarm is clear... inf... : hand phone number boğaziçi-cnc / okuma turkey servis+ 90 212 674 82 99 |
| only one led can be lit at a time depending on whether you are trying to chuck od or id if you were chucking od and need to change to id clamp down on nothing the led will go off move the opposite led until the light goes on unclamp the chuck the light will go off again at this point you can adjust it until it goes on again |
| jose luis sola mente tiene que estar uno prendido ala ves. cuando estas cambiando od o id por ejemplo, cuando lo chuck conla maquina chuck nada las dos led se apagan necesitas ajustar opusto led asta que la luz prenda y necesitas un chuck y eneste punto led se apagara entonses ajusta la luz asta que prenda cuando la luz esta prendida no se prendera la alarma att.robert |
| You need to make sure that when you are writing your program in IGF, on the screen where you enter your jaw dimensions, live center idmensions and so forth, that you tell it you are chucking on the ID. Then you need to go into your parameters mode. Item down one page and enter 1 for the value on OD/ID chucking. it's the same screen where you tell whether you're using your tailstock or not. |
| "OKUMA LR 25 980 ALARM-C PANEL1/CRP RECEIVE"
I need information about 980 Alarm-c panel1/crp receive, please help me somebody have the manual maintenence Okuma LR15? necesito informacion acerca de la alarma 980 Alarm-c panel1/crp receive, por favor ayuda, no puedo restablecer la alarma, alguien tiene el manual de esta maquina? |
Reply Options Share your opinions, advice, questions or comments on this post. | You must a registered user and logged in to use this feature: It is quick easy and offers many advantages when using our site. |
Social NetworkingShare this with your friends on facebook, twitter and Google+ | | Social sharing because it feels good:
| |
|
RelatedSome related posts that may be of interest to you. | Related posts: Related posts on other sites: |
Tags and TaggingTags help organize related posts and resources by topic. | • okuma • alarm • |
|
Computer Numerical Control
